High Tg PCB Advanced PCB Manufacturing| YMS PCB

Deskribapen laburra:

High-TG-Material start at around TG of 170°C. Most high-TG materials up to TG170°C are based on FR4 fibre-glass/epoxy compounds and are produced and processed like standard PCBs.

parametroak

Layers: 4L High Tg FR4 Material

Taula pentsamendua: 1,6 mm

Base Material:EM827 High tg

Min zuloak: 0,2 mm

Gutxieneko lerro zabalera / sakea ： 0,075 mm / 0,075 mm

Barne geruzaren arteko PTH arteko gutxieneko hutsunea Clear 0,2 mm-ra

Size：208mm×148mm

Aspektu: 8: 1

Surface treatment：Lead free HASL

Single-sided impedance 55Ω±10%, Differential impedance 100+7/-8Ω

Applications: Consumer electronics

Bidali email gurekin Jaitsi PDF gisa

Produktuen xehetasuna

Produktuen Tags

How do I classify high-TG materials?

Materiala	TG	MOT
FR4-standard-TG	130°C	110°C
FR4-mittel-TG	150°C	130°C
FR4-hoch-TG	170°C	150°C
Polyimid-Super-hoch-TG-Material	250°C	230°C

ome common high-frequency materials do not mention TGs in their datasheets. This is due to the original meaning of TG: "temperature of glass transition". Many ceramics- or PTFE-based materials do simply not contain any glass fibres and therefore have no technical TG. Generally, this fact also applies to Polyimides (PI). However, you can usually assume a TG of at least 200°C for Polyimide, ceramics or PTFE-materials. In this case the TG simply stands for temperature resistance.

You may apply the following values:

Material type	Typical „TG“
CEM1	110-130°C
FR4	120-180°C
PTFE	200-260°C
Ceramic	200-300°C
Polyimide	200-350°C

YMS High Tg PCB manufacturing capabilities:

YMS High Tg PCB manufacturing capabilities overview
Ezaugarria	gaitasunak
Geruza kopurua	3-60L
Geruza anitzeko PCB teknologia eskuragarri	16: 1 itxura erlazioa duen zulo pasagarria
	lurperatuta eta itsu bidez
	Hibridoa	High Frequency Material such as RO4350B and FR4 TG 180°Mix etc.
		High Speed Material such as M7NE and FR4 TG 180°Mix etc.
Lodiera	0,3 mm-8 mm
Gutxieneko lerroaren zabalera eta espazioa	0,05 mm / 0,05 mm (2 mil / 2 mil)
BGA PITCH	0,35 mm
Zulatutako neurri mekanikoa	0,15 mm (6 milia)
Zulo iragankorraren itxura erlazioa	16: 1
Azalera akabera	HASL, berunik gabeko HASL, ENIG, murgiltze latakoa, OSP, murgiltze zilarra, urrezko hatzarekin, galvanizatutako urrezko gogorra, OSP selektiboa ， ENEPIG.etc.
Bete Aukeraren bidez	Bidea estalita dago eta epoxi eroale edo ez-eroaleaz betetzen da, gero estalita eta estalita (VIPPO)
	Kobrea beteta, zilarrez betea
Izena ematea	± 4mil
Soldadura Maskara	Berdea, gorria, horia, urdina, zuria, beltza, morea, beltza matea, berde matea, etab.